2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 575
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
2. Test for 2.0 - 8.0 Ohms between control circuit terminal 6 and control circuit terminal 2.
瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater
element.
瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat cushion
heater element.
3. Disconnect the X2, X4 harness connectors at the HSM.
4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 20 X4 and the low reference circuit terminal 8 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
5. Connect the X1, X2, X4 harness connectors at the HSM.
6. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the HSM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
8. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
Rear Seat
DTC B2425 or B2430 (Rear Seat)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B2425 04
- Left Seat Heater Cushion Circuit Open
DTC B2425 0A
- Left Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2425 0B
- Left Seat Heater Cushion Circuit Current Above Threshold
DTC B2425 0C
- Left Seat Heater Cushion Circuit Current Below Threshold
DTC B2425 0D
- Left Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2425 0E
- Left Seat Heater Cushion Circuit Resistance Below Threshold
Showing posts with label Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat. Show all posts
Showing posts with label Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat. Show all posts
Saturday, November 30, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 564
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 564
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
2. Test for 2.0 - 8.0 Ohms between control circuit terminal 6 and control circuit terminal 2.
瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater
element.
瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat cushion
heater element.
3. Disconnect the X2, X4 harness connectors at the HSM.
4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 20 X4 and the low reference circuit terminal 8 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
5. Connect the X1, X2, X4 harness connectors at the HSM.
6. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the HSM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
8. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
Rear Seat
DTC B2425 or B2430 (Rear Seat)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B2425 04
- Left Seat Heater Cushion Circuit Open
DTC B2425 0A
- Left Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2425 0B
- Left Seat Heater Cushion Circuit Current Above Threshold
DTC B2425 0C
- Left Seat Heater Cushion Circuit Current Below Threshold
DTC B2425 0D
- Left Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2425 0E
- Left Seat Heater Cushion Circuit Resistance Below Threshold
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
2. Test for 2.0 - 8.0 Ohms between control circuit terminal 6 and control circuit terminal 2.
瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat cushion heater
element.
瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat cushion
heater element.
3. Disconnect the X2, X4 harness connectors at the HSM.
4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 20 X4 and the low reference circuit terminal 8 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
5. Connect the X1, X2, X4 harness connectors at the HSM.
6. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the HSM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
8. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
Rear Seat
DTC B2425 or B2430 (Rear Seat)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B2425 04
- Left Seat Heater Cushion Circuit Open
DTC B2425 0A
- Left Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2425 0B
- Left Seat Heater Cushion Circuit Current Above Threshold
DTC B2425 0C
- Left Seat Heater Cushion Circuit Current Below Threshold
DTC B2425 0D
- Left Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2425 0E
- Left Seat Heater Cushion Circuit Resistance Below Threshold
Thursday, November 28, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 536
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 536
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
2. Test for 3.5 - 11.5 Ohms between control circuit terminal 6 and control circuit terminal 4.
瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat back heater
element.
瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat back
heater element.
3. Disconnect the X2, X4 harness connectors at the HSM.
4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 10 X4 and the low reference circuit terminal 7 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
back heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat back heater element/temperature sensor.
5. Connect the X1, X2, X4 harness connectors at the HSM.
6. Disconnect the harness connector at the seat back heater element/temperature sensor.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the HSM.
8. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Back Cushion Heater Replacement (Escalade with HP2) ()Driver or Passenger Seat Back Cushion Heater
Replacement (Tahoe with HP2) ()Driver or Passenger Seat Back Cushion Heater Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
HP2 W/O Memory
DTC B2345 (HP2 w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B2345 00
- Seat Heater Disable Circuit
DTC B2345 13
- Seat Heater Elements Temperature Above Threshold
DTC B2345 42
- Seat Heater Elements Current Sensing Calibration Not Programmed
DTC B2345 4B
- Seat Heater Elements Current Sensing Calibration Out of Range
Diagnostic Fault Information
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
2. Test for 3.5 - 11.5 Ohms between control circuit terminal 6 and control circuit terminal 4.
瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat back heater
element.
瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat back
heater element.
3. Disconnect the X2, X4 harness connectors at the HSM.
4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 10 X4 and the low reference circuit terminal 7 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
back heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat back heater element/temperature sensor.
5. Connect the X1, X2, X4 harness connectors at the HSM.
6. Disconnect the harness connector at the seat back heater element/temperature sensor.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the HSM.
8. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Back Cushion Heater Replacement (Escalade with HP2) ()Driver or Passenger Seat Back Cushion Heater
Replacement (Tahoe with HP2) ()Driver or Passenger Seat Back Cushion Heater Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
HP2 W/O Memory
DTC B2345 (HP2 w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B2345 00
- Seat Heater Disable Circuit
DTC B2345 13
- Seat Heater Elements Temperature Above Threshold
DTC B2345 42
- Seat Heater Elements Current Sensing Calibration Not Programmed
DTC B2345 4B
- Seat Heater Elements Current Sensing Calibration Out of Range
Diagnostic Fault Information
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 530
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 530
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
2. Test for 3.5 - 11.5 Ohms between control circuit terminal 6 and control circuit terminal 4.
瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat back heater
element.
瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat back
heater element.
3. Disconnect the X2, X4 harness connectors at the HSM.
4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 10 X4 and the low reference circuit terminal 7 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
back heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat back heater element/temperature sensor.
5. Connect the X1, X2, X4 harness connectors at the HSM.
6. Disconnect the harness connector at the seat back heater element/temperature sensor.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the HSM.
8. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Back Cushion Heater Replacement (Escalade with HP2) ()Driver or Passenger Seat Back Cushion Heater
Replacement (Tahoe with HP2) ()Driver or Passenger Seat Back Cushion Heater Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
B2170
DTC B1925 or B2170 (HP2 or Dealer Installed w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1925 02
- Left Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B1925 05
- Left Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
DTC B2170 02
- Right Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B2170 05
- Right Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
Diagnostic Fault Information
Important: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat
unoccupied, then with the seat occupied.
2. Test for 3.5 - 11.5 Ohms between control circuit terminal 6 and control circuit terminal 4.
瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the seat back heater
element.
瀚慖f greater than the specified range, test the control circuits for an open/high resistance. If the circuits test normal, replace the seat back
heater element.
3. Disconnect the X2, X4 harness connectors at the HSM.
4. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 10 X4 and the low reference circuit terminal 7 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
back heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat back heater element/temperature sensor.
5. Connect the X1, X2, X4 harness connectors at the HSM.
6. Disconnect the harness connector at the seat back heater element/temperature sensor.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the HSM.
8. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Back Cushion Heater Replacement (Escalade with HP2) ()Driver or Passenger Seat Back Cushion Heater
Replacement (Tahoe with HP2) ()Driver or Passenger Seat Back Cushion Heater Replacement (without HP2) ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
B2170
DTC B1925 or B2170 (HP2 or Dealer Installed w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1925 02
- Left Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B1925 05
- Left Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
DTC B2170 02
- Right Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B2170 05
- Right Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
Diagnostic Fault Information
Subscribe to:
Posts (Atom)