2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 533
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
6. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
B2180
DTC B1935 or B2180 (Dealer Installed)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1935 04
- Left Seat Back Heater Circuit Open
DTC B1935 0A
- Left Seat Back Heater Circuit Rate of Change Below Threshold
DTC B1935 0B
- Left Seat Back Heater Circuit Current Above Threshold
DTC B1935 0C
- Left Seat Back Heater Circuit Current Below Threshold
DTC B1935 0D
- Left Seat Back Heater Circuit Resistance Above Threshold
DTC B1935 0E
- Left Seat Back Heater Circuit Resistance Below Threshold
DTC B1935 1F
- Left Seat Back Heater Circuit Intermittent
DTC B2180 04
- Right Seat Back Heater Circuit Open
DTC B2180 0A
- Right Seat Back Heater Circuit Rate of Change Below Threshold
DTC B2180 0B
- Right Seat Back Heater Circuit Current Above Threshold
DTC B2180 0C
- Right Seat Back Heater Circuit Current Below Threshold
DTC B2180 0D
- Right Seat Back Heater Circuit Resistance Above Threshold
DTC B2180 0E
- Right Seat Back Heater Circuit Resistance Below Threshold
DTC B2180 1F
- Right Seat Back Heater Circuit Intermittent
Diagnostic Fault Information
Showing posts with label test the signal circuit for a short to voltage. If the circuit tests normal. Show all posts
Showing posts with label test the signal circuit for a short to voltage. If the circuit tests normal. Show all posts
Thursday, November 28, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 523
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 523
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
6. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
HP2 W/O Memory
DTC B1935 or B2180 (HP2 w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1935 04
- Left Seat Back Heater Circuit Open
DTC B1935 0A
- Left Seat Back Heater Circuit Rate of Change Below Threshold
DTC B1935 0B
- Left Seat Back Heater Circuit Current Above Threshold
DTC B1935 0C
- Left Seat Back Heater Circuit Current Below Threshold
DTC B1935 0D
- Left Seat Back Heater Circuit Resistance Above Threshold
DTC B1935 0E
- Left Seat Back Heater Circuit Resistance Below Threshold
DTC B1935 1F
- Left Seat Back Heater Circuit Intermittent
DTC B2180 04
- Right Seat Back Heater Circuit Open
DTC B2180 0A
- Right Seat Back Heater Circuit Rate of Change Below Threshold
DTC B2180 0B
- Right Seat Back Heater Circuit Current Above Threshold
DTC B2180 0C
- Right Seat Back Heater Circuit Current Below Threshold
DTC B2180 0D
- Right Seat Back Heater Circuit Resistance Above Threshold
DTC B2180 0E
- Right Seat Back Heater Circuit Resistance Below Threshold
DTC B2180 1F
- Right Seat Back Heater Circuit Intermittent
Diagnostic Fault Information
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the HSM.
6. If all circuits test normal, replace the HSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the HSM replacement, setup, and programming
HP2 W/O Memory
DTC B1935 or B2180 (HP2 w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1935 04
- Left Seat Back Heater Circuit Open
DTC B1935 0A
- Left Seat Back Heater Circuit Rate of Change Below Threshold
DTC B1935 0B
- Left Seat Back Heater Circuit Current Above Threshold
DTC B1935 0C
- Left Seat Back Heater Circuit Current Below Threshold
DTC B1935 0D
- Left Seat Back Heater Circuit Resistance Above Threshold
DTC B1935 0E
- Left Seat Back Heater Circuit Resistance Below Threshold
DTC B1935 1F
- Left Seat Back Heater Circuit Intermittent
DTC B2180 04
- Right Seat Back Heater Circuit Open
DTC B2180 0A
- Right Seat Back Heater Circuit Rate of Change Below Threshold
DTC B2180 0B
- Right Seat Back Heater Circuit Current Above Threshold
DTC B2180 0C
- Right Seat Back Heater Circuit Current Below Threshold
DTC B2180 0D
- Right Seat Back Heater Circuit Resistance Above Threshold
DTC B2180 0E
- Right Seat Back Heater Circuit Resistance Below Threshold
DTC B2180 1F
- Right Seat Back Heater Circuit Intermittent
Diagnostic Fault Information
Wednesday, November 20, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 369
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 369
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.
3. If all circuits test normal, replace the amplifier.
DTC Set By Radio UQA with U42
1. Ignition OFF, disconnect the X3 harness connector at the amplifier.
2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.
* Left front low level audio signal (+) - terminal 15
* Left front low level audio signal (-) - terminal 7
* Right front low level audio signal (+) - terminal 14
* Right front low level audio signal (-) - terminal 6
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the radio.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.
3. Ignition OFF, reconnect the X3 harness connector at the amplifier.
4. Disconnect the X2 harness connector at the rear seat audio (RSA) module.
5. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.
* Left rear low level audio signal (+) - terminal 1
* Left rear low level audio signal (-) - terminal 2
* Right rear low level audio signal (+) - terminal 3
* Right rear low level audio signal (-) - terminal 4
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the rear seat audio (RSA) module.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)
module.
6. Ignition OFF, reconnect the X2 harness connector at the rear seat audio (RSA) module.
7. Disconnect the X3 harness connector at the amplifier.
8. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.
* Left rear low level audio signal (+) - terminal 13
* Left rear low level audio signal (-) - terminal 5
* Right rear low level audio signal (+) - terminal 12
* Right rear low level audio signal (-) - terminal 4
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the rear seat audio (RSA) module.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)
module.
9. If all circuits test normal, replace the amplifier.
DTC Set By Radio UQA with Y91 and U42 or UQS and U42
1. Ignition OFF, disconnect the X3 and X4 harness connectors at the amplifier.
2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.
* Left front low level audio signal (+) - terminal 11 X3
* Left front low level audio signal (-) - terminal 12 X3
* Right front low level audio signal (+) - terminal 3 X3
* Right front low level audio signal (-) - terminal 4 X3
* Left rear low level audio signal (+) - terminal 11 X4
* Left rear low level audio signal (-) - terminal 12 X4
* Right rear low level audio signal (+) - terminal 3 X4
* Right rear low level audio signal (-) - terminal 4 X4
* Subwoofer low level audio signal (+) - terminal 5 X4
* Subwoofer low level audio signal (-) - terminal 6 X4
* Center Channel low level audio signal (+) - terminal 13 X4
* Center Channel low level audio signal (-) - terminal 14 X4
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the radio.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.
3. If all circuits test normal, replace the amplifier.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.
3. If all circuits test normal, replace the amplifier.
DTC Set By Radio UQA with U42
1. Ignition OFF, disconnect the X3 harness connector at the amplifier.
2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.
* Left front low level audio signal (+) - terminal 15
* Left front low level audio signal (-) - terminal 7
* Right front low level audio signal (+) - terminal 14
* Right front low level audio signal (-) - terminal 6
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the radio.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.
3. Ignition OFF, reconnect the X3 harness connector at the amplifier.
4. Disconnect the X2 harness connector at the rear seat audio (RSA) module.
5. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.
* Left rear low level audio signal (+) - terminal 1
* Left rear low level audio signal (-) - terminal 2
* Right rear low level audio signal (+) - terminal 3
* Right rear low level audio signal (-) - terminal 4
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the rear seat audio (RSA) module.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)
module.
6. Ignition OFF, reconnect the X2 harness connector at the rear seat audio (RSA) module.
7. Disconnect the X3 harness connector at the amplifier.
8. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.
* Left rear low level audio signal (+) - terminal 13
* Left rear low level audio signal (-) - terminal 5
* Right rear low level audio signal (+) - terminal 12
* Right rear low level audio signal (-) - terminal 4
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the rear seat audio (RSA) module.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the rear seat audio (RSA)
module.
9. If all circuits test normal, replace the amplifier.
DTC Set By Radio UQA with Y91 and U42 or UQS and U42
1. Ignition OFF, disconnect the X3 and X4 harness connectors at the amplifier.
2. Radio ON, test for 5.0-7.5 volts between the appropriate signal circuit terminal listed below and ground.
* Left front low level audio signal (+) - terminal 11 X3
* Left front low level audio signal (-) - terminal 12 X3
* Right front low level audio signal (+) - terminal 3 X3
* Right front low level audio signal (-) - terminal 4 X3
* Left rear low level audio signal (+) - terminal 11 X4
* Left rear low level audio signal (-) - terminal 12 X4
* Right rear low level audio signal (+) - terminal 3 X4
* Right rear low level audio signal (-) - terminal 4 X4
* Subwoofer low level audio signal (+) - terminal 5 X4
* Subwoofer low level audio signal (-) - terminal 6 X4
* Center Channel low level audio signal (+) - terminal 13 X4
* Center Channel low level audio signal (-) - terminal 14 X4
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the radio.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the radio.
3. If all circuits test normal, replace the amplifier.
Subscribe to:
Posts (Atom)